2.4G WiFi Antenna with SMA Cable 3DBI Gain Antennas U.FL to for Arduino CC3000 ESP8266

Description:
Antenna length:10.8cm
Cable length:16cm
Extended range 3BI Adjustable WiFi Antenna with gold plated U.FL to Female SMA connection cable. If you are looking for extended WiFi range from your ESP8266, CC3000 or other WiFi based projects then this Antenna package is what you need.

If you have a U.FL connector (the ity bity one) then use the cable, else the next most popular is the full size SMA connector in which case the 3DBI Antenna will screw on directly.

There is an IPEX antenna holder on the top of the board, which can be connected to an external 2.4G antenna. (External antenna requires replacement of capacitor location)

The ESP32-C3 Super Mini is an IoT mini development board based on the Espressif ESP32-C3 Wi-Fi/Blue-tooth dual-mode chip.
The ESP32-C3 is a 32-bit RISC-V CPU containing a FPU (Floating Point Unit) for 32-bit single-precision arithmetic with powerful computational capabilities.
It has excellent RF performance and supports IEEE 802.11 b/g/n WiFi and Bluetooth 5 (LE) protocols. The board comes with an external antenna to enhance signal strength for wireless applications.
It also features a small and compact form factor combined with a single-sided surface mount design.
It is equipped with a rich set of interfaces, with 11 digital I/Os that can be used as PWM pins and 4 analogue I/Os that can be used as ADC pins, and it supports four serial interfaces, including UART, I2C and SPI.
There is also a small reset button and a bootloader mode button on the board.

Taken together, the ESP32 C3 Super Mini is positioned as a high-performance, low-power, cost-effective IoT mini development board for low-power IoT applications and wireless wearable applications.

Product Parameters
Powerful CPU: ESP32-C3, 32-bit RISC-V single-core processor, running at up to 160 MHz.
WiFi: 802.11b/g/n protocol, 2.4GhHz, supports Station mode, SoftAP mode, SoftAP+Station mode, Mixed mode
Blue-tooth: Blue-tooth 5.0
Ultra-low power consumption: deep sleep power consumption of about 43μA
Rich board resources: 400KB SRAM, 384KB ROM 4Mflash built-in.
Chip Model : ESP32C3FN4
Ultra-small size: as small as a thumb (22.52x18mm) in a classic form factor for wearables and small projects.
Reliable security features: cryptographic hardware accelerator with support for AES-128/256, hash, RSA, HMAC, digital signature and secure boot
Rich interfaces: 1xI2C, 1xSPI, 2xUART, 11xGPIO(PWM), 4xADC
Single-sided components, surface mount design
On-board LED blue light: GPIO8 pinout

External power supply
If you need external power supply just connect the external power supply + level to the 5V position and GND to the negative terminal. (Support 3.3～6V power supply).
Remember that when connecting the external power supply, you can not access the USB, USB and external power supply can only choose one.
Note: When welding, please be careful not to short-circuit the positive and negative terminals and burn the battery and equipment.

Q: Com port not recognized on Arduino
A: Enter download mode: Way 1: Press and hold BOOT to power up. Way 2: Press and hold the BOOT button of ESP32C3, then press the RESET button, release the RESET button, then release the BOOT button, at this time, ESP32C3 will enter the download mode. (You need to re-enter the download mode every time you connect, sometimes press it once, the port is unstable and will be disconnected, you can judge it by the port recognition sound)

Q: The program can not run after uploading
A: You need to press the Reset button to execute the program after successful upload.

Q: The serial port of ESP32C3SuperMini Arduino can not be printed.
A: You need to set the USB CDC On Boot in the toolbar to Enabled.

Package Included:
1 X ESP32 C3 Super Mini Board
1 X 3DBI WiFi Antenna
1 X U.FL to Female SMA Cable